Why Air Conditioning Servicing Matters
Most people treat air conditioning servicing the same way they treat the "check engine" light — something to deal with once there's a problem. The unit still blows cold, so why pay someone to look at it?
The honest answer is that the two most expensive things that go wrong in an air conditioner give you almost no warning, and both are cheap to prevent. Neither has anything to do with whether the unit is currently blowing cold air.
Key points
- Servicing is a set of electrical tests, not just a clean — capacitance, running current and insulation resistance all produce numbers you can track year on year.
- Dust in the indoor fan coil restricts airflow, traps heat around electrical components and is a real ignition risk.
- Australian supply voltage and summer heat degrade capacitors; a weak one burns out the motor or compressor it supports.
- Always ask for a written service report — it is your evidence for warranty and insurance claims.
1. Dust isn't a cleanliness issue. It's a safety issue.
The indoor fan coil unit is the part of the system that moves air through your home, which means it's also the part that collects everything in that air. Over a few seasons, dust builds up on the barrel fan, the coil fins, and the filters — and in ducted systems, right through the return air path.
Three things happen as that happens:
Airflow drops. A restricted coil means the fan motor works harder for less result. The motor runs hotter, draws more current, and wears out faster than it should.
Heat stops escaping. Dust is an insulator. A coated coil and a coated motor housing both hold heat in rather than shedding it.
Dust ends up where it shouldn't. Fan coil units contain electrical connections, a control board, and terminal blocks. A layer of dry, compacted lint sitting on or beside warm electrical components is a real ignition risk — and dust also traps moisture, which is how you get corrosion and tracking across terminals.
Fires are the worst case, not the typical case, and we don't want to overstate it. The far more common outcome is a burnt-out fan motor, a failed control board, or a unit that quietly costs you 20–30% more to run than it should. But the worst case is genuinely possible, and it's entirely avoidable with a clean.
If your system has never been serviced and it's more than a couple of summers old, this is the reason to book one — not efficiency.
2. Capacitors, and why Australian power supply is hard on them
This is the one almost no homeowner has heard of, and it's responsible for a large share of the mid-summer breakdowns we attend.
Your outdoor unit uses capacitors to start and run the compressor and the condenser fan motor. They're small cylindrical components, they cost very little, and they are consumable — they degrade and they are meant to be replaced.
Two things in Australia accelerate that degradation:
Voltage. Our nominal supply is 230V, with an allowable range of roughly 216–253V. In practice, plenty of suburbs sit near the top of that band, particularly during the day, and high rooftop solar penetration has pushed daytime voltages up further in a lot of areas. Spikes and sustained high voltage both shorten capacitor life.
Heat. These are electrolytic components sitting inside a metal box, often in full afternoon sun, in 40-degree ambient temperatures. Heat is the single biggest factor in how fast a capacitor loses capacitance.
Here's why it matters. A weak capacitor doesn't fail cleanly and stop the unit. It keeps working — badly. The motor it's meant to be supporting draws higher current, runs hotter, and struggles to start. Do that for a season and the failure moves from the capacitor to the motor windings. When it reaches the compressor, you're usually not repairing anything; you're quoting a new system.
A capacitor is one of the cheapest parts in your air conditioner. A compressor is often the reason people replace the whole unit. Testing capacitance takes a technician about two minutes with a meter, and it's the difference between a scheduled part swap and an unplanned replacement in January.
Servicing is a test regime, not a clean
This is the part that gets misunderstood most, and it's why "servicing" can mean two completely different things depending on who turns up.
Cleaning is the visible half. The half that actually protects you is a sequence of technical tests — mostly electrical — designed to find components that are still working but are on their way out. That's the entire point: catching the failure while it's still a part, before it becomes a system.
A proper service should include:
- Capacitance tested against the rated value on the component, not a visual check
- Running current measured on the compressor and both fan motors, compared to nameplate
- Supply voltage checked under load
- Insulation resistance on compressor windings where appropriate
- Contactors and relays inspected for pitting, heat damage and corrosion
- Terminal connections checked and re-tensioned — loose terminals generate heat
- Refrigerant pressures and temperature split measured to confirm charge and capacity
- Condensate drain flushed and fall confirmed
- Coils, barrel fan and filters cleaned; outdoor coil clearances checked
Every one of those produces a number. A number can be compared to last year's number. That's how you see a component degrading over three services instead of discovering it in a heatwave.
Always ask for a service report
Here's the practical test of whether you've had a real service: ask for the report.
A proper service report records the actual findings — the measured values, the components tested, anything flagged as marginal, and what was recommended. Not a tick-and-flick sheet saying "system serviced, operating correctly."
Three reasons this matters:
It's your only evidence the testing happened. If nobody wrote down a capacitance reading, there's a fair chance nobody took one.
It builds a history. A capacitor reading drifting down year on year tells you something a single visit never will. So does a compressor drawing progressively more current.
It matters for insurance and warranty. If you ever need to claim — fire, water damage from a blocked drain, or a manufacturer warranty claim on a failed compressor — documented evidence of regular professional servicing is often the difference between a claim being paid and being contested. Manufacturers can and do decline warranty claims where a system has clearly not been maintained. Landlords and commercial operators should treat the report as a compliance record, not a receipt.
Keep them. They're worth more than the invoice.
How often?
For most Melbourne, Geelong and Adelaide homes, once a year is the right answer, ideally in spring before the system gets pushed hard.
Six-monthly servicing is a commercial interval, not a residential one. It's the right call where a system runs long hours or under constant load — offices, retail, hospitality, aged care, server and comms rooms — or in the occasional home where the system runs close to continuously or sits in an unusually dusty environment. For a normal household, annual is enough.
If you've got an evaporative cooler as well, that's a separate seasonal job — those need a pre-summer service every year without exception, because they sit exposed on the roof for nine months doing nothing.